Tesla Model 3 Owners & Service Manuals

Tesla Model 3: Foam - Cushion - Driver Seat (Remove and Replace) - Remove

Tesla Model 3 2017-2024 Service Manual / Seats / Front Seat Covers Pads and Trims / Foam - Cushion - Driver Seat (Remove and Replace) / Foam - Cushion - Driver Seat (Remove and Replace) - Remove

Remove

  1. Remove the driver seat. See Seat - Driver (Remove and Replace).
  2. Remove the driver headrest trim. See Trim - Headrest - Driver (Remove and Replace).
  3. Remove the side outer cover from the driver seat. See Cover - Outer Side - Driver Seat (Remove and Install).

Foam - Cushion - Driver Seat (Remove and Replace)-Remove

  1. Release the clips that attach the inner side shield to the seat, and then pull the shield back to remove the shield from the seat.
  2. Remove the seat back shell from the seat. See Shell - Seat Back - Driver (Remove and Replace).
  3. Unhook the lower flaps that cover the LH and RH lower corners of the seat back frame.
  4. Unhook the upper flaps that cover the LH and RH lower corners of the seat back frame.

Foam - Cushion - Driver Seat (Remove and Replace) - Remove

  1. Release the clips that attach the outboard side of the seat back cover to the seat back frame, and then expose the air bag connector.

Foam - Cushion - Driver Seat (Remove and Replace)-Remove

  1. Disconnect the electrical harness from the driver side airbag connector.

Foam - Cushion - Driver Seat (Remove and Replace)-Remove

  1. Disconnect the electrical harness from the recliner motor connector.

Foam - Cushion - Driver Seat (Remove and Replace)-Remove

  1. Disconnect the electrical harness from the ECU connector.

Foam - Cushion - Driver Seat (Remove and Replace)-Remove

  1. Disconnect the electrical harness from the lumbar pump connector.

Foam - Cushion - Driver Seat (Remove and Replace)-Remove

  1. Release the clips that attach the electrical harness to the seat frame.

Foam - Cushion - Driver Seat (Remove and Replace)-Remove

  1. Disconnect the electrical wiring harness from the seat heater connectors.

Foam - Cushion - Driver Seat (Remove and Replace) - Remove

  1. Release the clips that attach the seat heater connectors to the seat underside, and then separate the connectors from the seat underside.
  2. Remove the seatbelt buckle. See Buckle - 1st Row - LH (Remove and Replace).

Foam - Cushion - Driver Seat (Remove and Replace)-Remove

  1. Remove and discard the bolts (x4) that attach the seat back to the seat cushion, and then remove the seat back from the cushion.   Torque 43 Nm

Foam - Cushion - Driver Seat (Remove and Replace)-Remove

  1. Disconnect the electrical harness from the seat occupied sensor connector.

Foam - Cushion - Driver Seat (Remove and Replace)-Remove

  1. Release the clip that attaches the seat occupied sensor to the seat underside, and then separate the sensor from the seat underside.

Foam - Cushion - Driver Seat (Remove and Replace)-Remove

  1. Release the clips (x2) that attach the seat cushion foam to the seat suspension.
  2. Release the clips (x3) that attach the seat cushion foam to the seat cushion frame at the front, inboard, and outboard sides, and then remove the foam from the frame.

Note: Make sure that the seat heater connector and seat occupied sensor assembly does not catch on the seat suspension or frame

    READ NEXT:

     Foam - Cushion - Driver Seat (Remove and Replace) - Install

    Install Install the seat cushion foam to the seat cushion frame, and then fasten the clips (x3) that attach the foam to the frame at the outboard and inboard sides, and at the front. Note: Make

     2nd Row Seat Covers Pads and Trims

     Cover - Seat Back - 2nd Row Seat - RH (Remove and Replace)

    Remove Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace). Remove the RH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove an

    SEE MORE:

     Stabilizer Bar - Rear (Remove and Replace)

      Remove Raise and support the vehicle. See Raise Vehicle - 2 Post Lift. Remove the mid aero shield panel. See Panel - Aero Shield - Mid (Remove and Replace).  

     Harness - Windshield- Install

    Install Secure the clips that attach the windshield harness to the RH A-pillar. Connect the windshield harness electrical connectors. Install the forward facing camera. See Camera - Forward Facing (Remove and Replace). Secure the windshield harness with the clips along the top of th

    © 2019-2024 Copyright www.tmodel3.com