Tesla Model 3 Owners & Service Manuals

Tesla Model 3: Gearbox Fluid - Front Drive Unit - Drain

Tesla Model 3 2017-2024 Service Manual / Front Drive Unit / Front Gearbox and Halfshafts / Gearbox Fluid - Front Drive Unit (Drain and Refill) / Gearbox Fluid - Front Drive Unit - Drain

SPECIAL TOOLS

KIT, DRIVE UNIT OIL DRAIN, MODEL 3 (1134264-00-A)

KIT, DRIVE UNIT OIL FILL, MODEL 3 (1139126-00-A)

Tool, DUF Dipstick, Model 3 (1446276-20-A)

SWITCHBOX, OIL PUMP, MODEL 3 (1131264-00-A)

JUMP START, XP-10 (1129348-00-A )

Skt, Oil Filter, 63.5mm X 14 (1130484-00-A)

Drain

  1. Remove the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).

  Gearbox Fluid - Front Drive Unit - Drain

  1. Release the grey locking tab, and then press down on the tab to disconnect the oil pump connector.
  2. Position an oil drain container underneath the front drive unit oil filter.

  Gearbox Fluid - Front Drive Unit - Drain

  1. Use an oil filter socket to remove the front drive unit oil filter.

  Gearbox Fluid - Front Drive Unit - Drain

  1. Install the oil drain adapter on the front drive unit oil filter housing.

  Gearbox Fluid - Front Drive Unit - Drain

  1. Connect the fluid evacuator tube to the oil drain adapter, and then place the other end of the tube in the oil drain container.

  Gearbox Fluid - Front Drive Unit - Drain

  1. Connect the oil pump switchbox and XP-10 jump pack to the front drive unit oil pump.
  2. Press and hold the button on the oil pump switchbox until oil stops pumping out.
  3. Wait 60 seconds, and then once again press and hold the button on the oil pump switchbox until oil stops pumping out.
  4.  Disconnect the oil pump switchbox and XP-10 jump pack from the front drive unit oil pump.

  Gearbox Fluid - Front Drive Unit - Drain

  1. Disconnect the fluid evacuator tube from the oil drain adapter.

  Gearbox Fluid - Front Drive Unit - Drain

  1. Remove the oil drain adapter from the front drive unit oil filter housing.

 Caution: If the oil drain adapter o-ring seal transferred to the front drive unit oil filter housing, place the seal back on the oil drain adapter.

  Gearbox Fluid - Front Drive Unit - Drain

  1. Apply a light coat of ATF-9 to the o-ring seal on a new oil filter, and then install the filter on the front drive unit oil filter housing. Torque 3 Nm + 135 degrees

    READ NEXT:

     Gearbox Fluid - Front Drive Unit - Refill

    Refill   Remove the fill plug.

     Halfshaft - Front Drive Unit - LH (Remove and Replace)

     Halfshaft - Front Drive Unit - LH - Remove

      SPECIAL TOOLS Tool, Axle Extraction, Model 3 (1133386-00-A) Tool, Hub Puller, Hydraulic (10

    SEE MORE:

     Trim - Sill Panel - Rear - LH (Remove and Replace)

    Remove Open all doors. Lower all windows. Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace). Remove the LH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace). Pull upward at the lower corner of the rea

     Seal - Glass Run - Front Door - LH (Remove and Replace)-  Install

    Install Position the new LH front door glass run seal on the LH front door.  Tip: If necessary, apply a small amount of P80 lubricant on the length of the seal to aid installation. Position the LH door mirror on the LH front door, and then install the clip that attaches the mirr

    © 2019-2024 Copyright www.tmodel3.com