Tesla Model 3 Owners & Service Manuals

Tesla Model 3: Foam - Backrest - Driver Seat (Remove and Replace) - Remove

Tesla Model 3 2017-2023 Service Manual / Seats / Front Seat Covers Pads and Trims / Foam - Backrest - Driver Seat (Remove and Replace) / Foam - Backrest - Driver Seat (Remove and Replace) - Remove

Remove

Foam - Backrest - Driver Seat (Remove and Replace)- Remove

  1. Remove the driver seat. See Seat - Driver (Remove and Replace).
  2. Remove the driver headrest trim. See Trim - Headrest - Driver (Remove and Replace).
  3. Remove the side outer cover from the driver seat. See Cover - Outer Side - Driver Seat (Remove and Install).
  4. Release the clips that attach the inner side shield to the seat, and then pull the shield back to remove the shield from the seat.
  5. Remove the seat back shell from the seat. See Shell - Seat Back - Driver (Remove and Replace).
  6. Unhook the lower flaps that cover the LH and RH lower corners of the seat back frame.
  7. Unhook the upper flaps that cover the LH and RH lower corners of the seat back frame.

Foam - Backrest - Driver Seat (Remove and Replace)- Remove

  1. Release the clips that attach the outboard side of the seat back cover to the seat back frame, and then expose the air bag connector.

Foam - Backrest - Driver Seat (Remove and Replace)- Remove

  1. Disconnect the electrical harness from the side airbag connector.

Foam - Backrest - Driver Seat (Remove and Replace)- Remove

  1. Remove and discard the nuts that attach the side airbag to the seat back frame, and then pull the studs of the airbag out of the frame.   Torque 5.4 Nm

Foam - Backrest - Driver Seat (Remove and Replace)- Remove

  1. Disconnect the electrical harness from the recliner motor connector.

Foam - Backrest - Driver Seat (Remove and Replace)- Remove

  1. Disconnect the electrical harness from the ECU connector.

Foam - Backrest - Driver Seat (Remove and Replace)- Remove

  1. Disconnect the electrical harness from the lumbar pump connector.

Foam - Backrest - Driver Seat (Remove and Replace)- Remove

  1. Release the clips that attach the electrical harness to the seat frame, and then remove the electrical harness from the seat frame.

Foam - Backrest - Driver Seat (Remove and Replace)- Remove

  1. Disconnect the electrical harness from the seat heater connectors.
  1. Release the clips that attach the seat heater connectors to the seat underside, and then separate the connectors from the seat underside.

Foam - Backrest - Driver Seat (Remove and Replace)- Remove

  1. Release the clips that attach the backrest foam to the seat back frame.

Note: Release the clips at the bottom and work up.

  1. Remove the bottom of the backrest foam from the seat back frame, and then lift the foam straight up and off the frame.
  2. Remove the driver side airbag from the pocket within the seatback cover.

Note: Make sure that the driver side airbag mounting studs do not catch in the holes of the pocket.

    READ NEXT:

     Foam - Backrest - Driver Seat (Remove and Replace) - Install

    Install Install the driver side airbag into the pocket within the seatback cover. Note: Make sure that the driver side airbag mounting studs extend out of the holes of the pocket. Install the

     Foam - Cushion - Driver Seat (Remove and Replace)

     Foam - Cushion - Driver Seat (Remove and Replace) - Remove

    Remove Remove the driver seat. See Seat - Driver (Remove and Replace). Remove the driver headrest trim. See Trim - Headrest - Driver (Remove and Replace). Remove the side outer cover from the dr

    SEE MORE:

     HV Battery (Dual Motor) - Remove

    SPECIAL TOOLSAdapter, Lift Pad, Model 3 (1453419-00-A)Key, Seat Belt Release, Model 3 (1133787-00-A) ASY, Battery Table, Manual Lift (1020566-00-F)Top Plate, Battery Table, Manual Lift (1020566-99-A) Hoist, H-Frame EMEA (1129166-00-A)Kit, Alignment Rods, Battery, Model 3 (1134523-00-

     Fender Assembly - Front - LH (Remove and Replace)- Install

    Install Install the underhood storage unit clips (3x) on the new LH front fender. Note: Replace any broken or damaged clips. Install the headlight grommet on the new LH front fender. Position the LH cowl screen carrier bracket on the new LH front fender, and then install the cli

    © 2019-2023 Copyright www.tmodel3.com