Tesla Model 3 Owners & Service Manuals

Tesla Model 3: Harness - Thermal Beam- Install

Tesla Model 3 2017-2024 Service Manual / Electrical / Harnesses / Harness - Thermal Beam (Remove and Replace) / Harness - Thermal Beam- Install

Install

Harness - Thermal Beam- Install

  1. Fasten the clips that attach the thermal beam electrical harness to the shock tower brace.
  2. Install the bolt that attaches the thermal beam electrical harness ground terminal to the RH shear wall. Torque 10 Nm

Harness - Thermal Beam- Install

  1. Connect the thermal beam electrical harness to the powertrain pump to sill hose coolant temperature sensor connector.

Harness - Thermal Beam- Install

  1. Connect the thermal beam electrical harness to the superbottle level sensor connector.

Harness - Thermal Beam- Install

  1. Fasten the clip that attaches the thermal beam electrical harness to the suction/liquid lines.

Harness - Thermal Beam- Install

  1. Fasten the clip that attaches the thermal beam electrical harness to the superbottle.

Harness - Thermal Beam- Install

  1. Install the thermal beam electrical harness to the chiller and EXV assembly hose, and then fasten the clip that attaches the electrical harness to the hose.

Harness - Thermal Beam- Install

  1. Fasten the clip that attaches the thermal beam electrical harness to the superbottle.

Harness - Thermal Beam- Install

  1. Connect the thermal beam electrical harness to the powertrain coolant pump connector.
  2. Connect the thermal beam electrical harness to the HV battery coolant pump connector.

Harness - Thermal Beam- Install

Harness - Thermal Beam- Install

  1. Connect the thermal beam electrical harness to the 5-way valve actuator connector.

Harness - Thermal Beam- Install

  1. Connect the thermal beam electrical harness to the coolant temperature sensor connector.

Harness - Thermal Beam- Install

  1. Connect the thermal beam electrical harness to the chiller and EXV assembly connector.

Harness - Thermal Beam- Install

  1. Connect the thermal beam electrical harness to the low pressure transducer connector.

Harness - Thermal Beam- Install

  1. Fasten the clips that attach the thermal beam electrical harness to the compressor and compressor bracket.

Harness - Thermal Beam- Install

  1. Connect the thermal beam electrical harness to the high pressure transducer connector.

Harness - Thermal Beam- Install

  1. Connect the thermal beam electrical harness to the compressor connector.

Harness - Thermal Beam- Install

  1. Install the bolt that attaches the thermal beam electrical harness ground terminal to the compressor. Torque 6 Nm

Harness - Thermal Beam- Install

  1. Fasten the clip that attaches the suction/liquid lines to the body near the TXV.

Harness - Thermal Beam- Install

  1. Connect the thermal beam electrical harness to the front body controller module connector.

Harness - Thermal Beam- Install

  1. Install the thermal beam electrical harness cover to the front body controller module, and then install the bolt that attaches the cover to the module. Torque 6 Nm

Harness - Thermal Beam- Install

  1. Install the HVAC plenum outer duct to the HVAC plenum inner duct, and then fasten the clips that attach the outer duct to the inner duct.
  2. Connect 12V power. See 12V Power (Disconnect and Connect).
  3. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).

    READ NEXT:

     Harness - Trunk (Remove and Replace)

     Harness - Trunk- Remove

    Remove Remove the package tray trim. See Trim - Package Tray (Remove and Install). Disconnect the trunk electrical harness connectors. Remove and discard the bolt that attaches the gro

     Harness - Trunk- Install

    Install Move the trunk electrical harness in through the trunk bulkhead. Fasten the clips that attach the trunk electrical harness to the trunk lid. Install new bolts (x2) to attach th

    SEE MORE:

     Wheels and Tires

    Note: For instructions on how to jack/lift Model 3 Tire Specifications (Factory) Tire pressures vary depending on the type of tires fitted. Refer to the tire pressures printed on the Tire and Loading Information label. This label is located on the center door pillar and is visible wh

     Breather - Front Drive Unit (Remove and Replace)

    Remove Remove the front subframe assembly. See Subframe Assembly - Front (Dual Motor) (Remove and Install). Remove the front drive unit breather. Torque 5 Nm Install Installation procedure is the reverse of removal.

    © 2019-2024 Copyright www.tmodel3.com