Tesla Model 3 Owners & Service Manuals

Tesla Model 3: Module - Cooling Fan - Install

Install

Module - Cooling Fan- Install

LH Side
LH Side

RH Side
RH Side

  1. With an assistant, put the cooling fan module into position from below the vehicle, and then hand-tighten the bolts that attach the bottom of the cooling fan module to the ankle catcher.

Note: Make sure that the lower seal from the cooling fan module and lower active shutter grille are sitting flush against each other.

  1. Tighten the LH and RH bolts that attach the lower portion of the cooling fan module to the ankle catcher. Torque 10 Nm
  2. Install a new o-ring onto the discharge line, and then install the discharge line into the cooling fan module.

Module - Cooling Fan - Install

  1. Install the nut that attaches the discharge line to the cooling fan module. Torque 22 Nm
  2. Install a new o-ring onto the suction/liquid line, and then install the suction line into the cooling fan module.
  3. Install the nut that attaches the suction/liquid line to the cooling fan module. Torque 22 Nm

Module - Cooling Fan - Install

  1. After installing the suction/liquid line, recharege the refrigerant. See A/C Refrigerant (Recovery and Recharge).

Note: Perform installation of components removed concurrently with refrigerant recharge.

  1. Position the coolant drain underneath the RH side of the vehicle.

Module - Cooling Fan - Install

  1. Remove the hose plug, and then install the radiator outlet hose to the cooling fan module. Secure the hose with clip.
  2. Position the coolant drain underneath the LH side of the vehicle.

Module - Cooling Fan - Install

  1. Remove the hose plug, and then install the radiator inlet hose to the cooling fan module. Secure the hose with clip.
  2. Remove the coolant drain container from underneath the vehicle.

Module - Cooling Fan - Install

  1. Connect the electrical harness to the cooling fan connector.
  2. Install the front valance. See Valance - Front Fascia (Remove and Replace).
  3. Install the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  4. Lower the vehicle fully.

Module - Cooling Fan - Install

  1. Slide the underhood reinforcement bracket onto the top of the cooling fan module.

Note: The cooling fan module tab must be inserted into the isolator so that the trailing tab touches the isolator rubber and the chamfered edge is clearly visible when looking from above.

Note: The trailing edge of the cooling fan module mount must contact the lower tunnel of the isolator.

Module - Cooling Fan - Install

Module - Cooling Fan - Install

  1. Install the bolts that attach the underhood reinforcement bracket to the body.  Torque 16 Nm

Note: Make sure that there is space between the cooling fan module and the isolator bar to avoid vibration.

Module - Cooling Fan - Install

  1. Loosen the bolts that attach the LH side cooling fan module isolator.

Module - Cooling Fan - Install

  1. Push the LH side of the cooling fan module isolator towards the front of the vehicle until the isolator bottoms out at the top.
  2. Tighten the bolts that attach the LH side cooling fan module isolator. Torque 6 Nm
  3. Repeat step 19 through step 21 for the RH side cooling fan module isolator.
  4. Check the coolant level at the superbottle and add coolant to the full line, if needed.

Module - Cooling Fan - Install

  1. Connect the active grille shutter electrical connector.
  2. Connect 12V power. See 12V Power (Disconnect and Connect).
  3. After the A/C refrigerant recharge has fully completed, verify the operation of the A/C system.
  4. Perform the cooling system vacuum refill. See Cooling System (Vacuum Refill).
  5. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  6. Install the hood latch cover. See Cover - Hood Latch (Remove and Replace).
  7. Install the outer HVAC plenum duct. See Duct - HVAC Plenum - Outer (Remove and Replace).
  8. Install the cabin intake duct. See Duct - Cabin Intake (Remove and Replace).
  9. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).

    READ NEXT:

     Module - Cooling Fan (Remove and Replace)

    Remove Remove the cooling fan module. See Module - Cooling Fan (Remove and Install). Release the clips (x14) that attach the active grille shutter to the cooling fan module, and then re

     Mounting - A/C Compressor (Remove and Replace)

    Remove Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace). Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace). Remov

     Pipe - High Pressure - Compressor to Condenser (Remove and Replace)

    SEE MORE:

     Strap - 12V Battery (Remove and Replace)

    Remove Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace). Remove the cabin intake duct. See Duct - Cabin Intake (Remove and Replace). Loosen the nut that attaches the 12V battery upper tie down bracket to the 12V battery strap. Torque 5 Nm Push down and s

     ECU - Charge Port (Remove and Replace)

    Remove Open the trunk. Remove the LH trunk side trim. See Trim - Side - Trunk - LH (Remove and Replace). Disconnect 12V power. See 12V Power (Disconnect a

    © 2019-2024 Copyright www.tmodel3.com