Tesla Model 3: Thermal Management
Tesla Model 3 2017-2026 Service Manual / Thermal Management
- Cabin HVAC
- Actuator - Bleed - LH (Remove and Replace)
- Actuator - Intake (Remove and Replace)
- Actuator - Lower Mode (Remove and Replace)
- Actuator - Upper Mode (Remove and Replace)
- Actuator - Vent - LH (Remove and Replace)
- Actuator - Vent - RH (Remove and Replace)
- Air Extractor - LH (Remove and Replace)
- Duct - Air Wave - LH (Remove and Replace)
- Duct - Air Wave - RH (Remove and Replace)
- Duct - Cabin Intake (Remove and Replace)
- Duct - Footwell - LH (Remove and Replace)
- Duct - Footwell - RH (Remove and Replace)
- Duct - HVAC Plenum - Inner (Remove and Replace)
- Duct - HVAC Plenum - Outer (Remove and Replace)
- Filter - Cabin (Remove and Replace)
- Heater - PTC (Remove and Replace)
- HVAC Assembly (Remove and Replace)
- Blower Motor - HVAC (Remove and Replace)
- Sensor - Ambient Air Temperature (Remove and Replace)
- Sensor - Cabin Temperature (Remove and Replace)
- Sensor - Temperature - Evaporator (Remove and Replace)
- Sensor - Temperature - LH (Remove and Replace)
- Sensor - Temperature - RH (Remove and Replace)
- Refrigerant System
- A/C Refrigerant Leak Detection
- A/C Refrigerant (Recovery and Recharge)
- Chiller and EXV Assembly (Remove and Replace)
- Compressor (Remove and Replace)
- Condenser (Remove and Replace)
- Evaporator (Clean)
- Evaporator (Remove and Replace)
- Module - Cooling Fan (Remove and Install)
- Module - Cooling Fan (Remove and Replace)
- Mounting - A/C Compressor (Remove and Replace)
- Pipe - High Pressure - Compressor to Condenser (Remove and Replace)
- Pipes - Refrigerant - High / Low Pressure (Remove and Replace)
- Pressure Transducer - High Pressure (Remove and Replace)
- Pressure Transducer - Low Pressure (Remove and Replace)
- Receiver Dryer and Desiccant (Remove and Replace)
- TXV Valve - Evaporator (Remove and Replace)
- Cooling System
- 5-Way Valve (Remove and Replace)
- Actuator - 5-Way Valve (Dual Motor) (Remove and Replace)
- Actuator - 5-Way Valve (RWD) (Remove and Replace)
- Coolant Pump - HV Battery (Remove and Replace)
- Coolant Pump - Powertrain (Remove and Replace)
- Cooling System (Check and Fill)
- Cooling System (Drain and Refill)
- Cooling System (Partial Refill and Bleed)
- Cooling System (Vacuum Refill)
- Hose - Chiller to Car Computer and HV Battery Supply Manifold (Dual Motor) (Remove and Replace)
- Hose - Return - HV Battery (Remove and Replace)
- Hose - Return - Powertrain (Remove and Replace)
- Hose - Supply - Powertrain (Remove and Replace)
- Radiator (Remove and Replace)
- Superbottle (Dual Motor) (Remove and Replace)
- Superbottle (RWD) (Remove and Replace)
- Air Distribution
READ NEXT:
Actuator - Bleed - LH (Remove and Replace)
Remove
Remove the cross car beam. See
Beam - Cross Car (Remove and Replace).
Disconnect the electrical wiring harness connector from the LH bleed
actuator.
Remove the bolts that attac
Actuator - Intake (Remove and Replace)
Remove
Remove the HVAC assembly. See
HVAC Assembly (Remove and Replace).
Disconnect the electrical harness from the intake actuator connector.
Remove the screws (x2) that attach the int
SEE MORE:
Charge Port - Manual Release of Cable
DRAFT
Warning:
This procedure was derived from pre-production computer models, and
might not reflect the real-world situation. Warnings and cautions might be
missing. Follow safety requirements and use extreme caution when working on or
near high voltage systems and components
Procedure
Ensu
Subframe Assembly - Rear - Install
Install
Position the subframe lifting tool and subframe underneath the vehicle.
Connect the air line to the subframe lifting tool.
With an assistant, slowly raise the rear drive unit and subframe into
position.
Caution:
Assist with the routing of HV harnesses and coolant hoses through
compo
© 2019-2026 Copyright www.tmodel3.com
