Tesla Model 3 Owners & Service Manuals

Tesla Model 3: Door Assembly - Charge Port (NA) - Install

Install

  1. Install the charge port door onto the vehicle, and then attach the charge port door with clips. Note: Position the charge port door, then push the electrical harness through the opening and push up to attach the upper tabs, and then inwards to attach the lower clips.

  Door Assembly - Charge Port (NA) - Install

  1. Install the charge port door grommet onto the body
  2. Align the charge port with the 2 guide tabs, and then position the charge port in position.

  Door Assembly - Charge Port (NA) - Install

  1. Install the clips that attach the charge port electrical harness to the body.

  Door Assembly - Charge Port (NA) - Install

  1. Install the bolt that attaches the charge port harness bracket to the body. Torque 6 Nm

  Door Assembly - Charge Port (NA) - Install

  1. Install the bolts that attach the charge port to the body. Torque 6 Nm

  Door Assembly - Charge Port (NA) - Install

  1. Install the bolt that attaches the charge port ground bolt to the body. Torque 6 Nm

  Door Assembly - Charge Port (NA) - Install

  1. Install the clips that attach the charge port closeout panel.

  Door Assembly - Charge Port (NA) - Install

  1. Connect the low voltage charge port ECU electrical connectors.

  Door Assembly - Charge Port (NA) - Install

  1. Install the edge clip that attaches the HV harness to the charge port closeout panel.
  2. Remove the masking tape from the charge port door area.
  3. Install the LH taillight. See Taillight - LH (Remove and Replace).

  Door Assembly - Charge Port (NA) - Install

  1. Install the LH trunk stop.
  2. Install the LH trunk side trim. See Trim - Side - Trunk - LH (Remove and Replace).
  3. Install the trunk garnish. See Garnish - Trunk (Remove and Replace).
  4. Install the trunk sill trim panel. See Trim - Sill - Trunk (Remove and Replace).
  5. Install the trunk floor trim. See Trim - Floor - Trunk (Remove and Replace).
  6. Install the LH 2nd row seat back. See Seat Back - 2nd Row - LH (Remove and Install).
  7. Perform the penthouse air leak test. See Penthouse Air Leak Test.

  Door Assembly - Charge Port (NA) - Install

  1. Connect the charge port to HV battery harness from the DC input assembly.

Note: Make sure that the locking tab is secured.

  Door Assembly - Charge Port (NA) - Install

  1. Install the clip that attaches the charge port to HV battery harness to the LH lower C-pillar.

  Door Assembly - Charge Port (NA) - Install

  1. Install the bolts that attach the charge port to HV battery harness bracket at the penthouse, and attach the electrical harness with clips (x2). Torque 10 Nm
  2. Install the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  3. Install the LH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).

  Door Assembly - Charge Port (NA) - Install

  1. Install the HV cap that covers the HV harness located on the LH side of the penthouse.
  2. Reconnect 12V power. See 12V Power (Disconnect and Connect).
  3. Connect a laptop with Toolbox to the vehicle.
  4. In Toolbox, type "CP" in the search tab. Note: Make sure that "Actions" is selected, if not already.
  5. In Toolbox, click the play button next to "TEST-SELF_ CP_X_FUNCTIONAL", and then click "Run".
  6. In Toolbox, click the play button next to "TEST-SELF_ CP_X_UHF", and then click "Run".
  7. Disconnect the laptop from the vehicle.
  8. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  9. Close the hood and the trunk.
  10. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).

    READ NEXT:

     Door Assembly - Charge Port (China) (Remove and Replace)

     Door Assembly - Charge Port (China) - Remove

      SPECIAL TOOLS Insulation Multimeter, Fluke 1508 (1076921-01-B) Test Probes, Slim

     Door Assembly - Charge Port (China) - Install

    Install Install the charge port door assembly on the vehicle: Pivot the assembly so that the actuator mechanism clears underneath the quarter pan

    SEE MORE:

     Door - Rear - LH (Remove )

    Remove Open the rear LH door, pass a shop towel halfway through the striker, and then close the door so that it rests against the shop towel. Remove the rear LH door glass. Remove the LH rear door outer belt seal. Remove the LH rear window regulator.  See  Window Motor / Regula

     Pipe - High Pressure - Compressor to Condenser- Remove

    Remove Raise and support the vehicle. See Raise Vehicle - 2 Post Lift. Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace). Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace). Remove the cabin intake duct. See Duct -

    © 2019-2024 Copyright www.tmodel3.com