Tesla Model 3: Closures
Tesla Model 3 2017-2026 Service Manual / Closures
- Closure Assist Mechanisms and Hinges
- Gas Strut - Hood - LH (Remove and Replace)
- Gas Strut - Trunk - LH (Remove and Replace)
- Hinge - Hood - LH (Remove and Replace)
- Hinge - Trunk - LH (Remove and Replace)
- Latches Strikers and Pinch Sensors
- Actuator - Latch - Hood - Primary (Remove and Replace)
- Actuator - Latch - Hood - Secondary (Remove and Replace)
- Latch - Door - Front - LH (Remove and Replace)
- Latch - Door - Rear - LH (Remove and Replace)
- Latch - Hood (Remove and Replace)
- Latch - Trunk (Remove and Replace)
- Manual Release - Door - Rear - LH (Actuate)
- Striker - Door - Front - LH (Remove and Replace)
- Striker - Door - Rear - LH (Remove and Replace)
- Striker - Hood (Remove and Replace)
- Striker - Trunk (Remove and Replace)
- Switch - Exterior Release - Trunk (Remove and Replace)
- Exterior Door Handles
- Hall Sensor - Exterior Release - Door - Front - LH (Remove and Replace)
- Hall Sensor - Exterior Release - Door - Rear - LH (Remove and Replace)
- Handle - Exterior Release - Door - Front - LH (Adjust)
- Handle - Exterior Release - Door - Front - LH (Remove and Replace)
- Handle - Exterior Release - Door - Rear - LH (Adjust)
- Handle - Exterior Release - Door - Rear - LH (Remove and Replace)
- Door Glass and Regulators
- Glass - Door - LH - Front (Adjust)
- Glass - Door - LH - Front (Remove and Replace)
- Glass - Door - LH - Rear (Adjust)
- Glass - Door - LH - Rear (Remove and Replace)
- Switch - Window - Driver (Remove and Replace)
- Switch - Window - Front Passenger (Remove and Replace)
- Switch - Window - Rear (Remove and Replace)
- Window Motor / Regulator Assembly - Front - LH (Remove and Replace)
- Window Motor / Regulator Assembly - Rear - LH (Remove and Replace)
- Window Regulator - Front - LH (Recalibrate)
- Window Regulator - Rear - LH (Recalibrate)
- Seals Body Closures
- Closeout Panel - Door - Front - LH (Remove and Install)
- Seal - Body - Side - Front - Primary - LH (Remove and Replace)
- Seal - Body - Side - Rear - Primary - LH (Remove and Replace)
- Seal - Glass Run - Front Door - LH (Remove and Replace)
- Seal - Hood (Remove and Replace)
- Seal - Inner Belt - Front Door - LH (Remove and Replace)
- Seal - Inner Belt - Rear Door - LH (Remove and Replace)
- Seal - Outer Belt - Front Door - LH (Remove and Replace)
- Seal - Outer Belt - Rear Door - LH (Remove and Replace)
- Seal - Secondary - Front Door - LH (Remove and Replace)
- Seal - Secondary - Rear Door - LH (Remove and Replace)
- Seal - Trunk (Remove and Replace)
READ NEXT:
Gas Strut - Hood - LH (Remove and Replace)
Remove
Open the hood.
Use a prop to attach the hood assembly in the open position.
Release the clip that attaches the hood gas strut to the hood mount.
Release the clip that attaches t
Gas Strut - Trunk - LH (Remove and Replace)
Remove
Open the trunk, and support the trunk in the open position.
Release the clip that attaches the lower end of the LH trunk gas strut
to the hinge on the vehicle.
Release the cl
SEE MORE:
Door Assembly - Charge Port (NA) (Remove and Replace)
Door Assembly - Charge Port (NA) - Remove
Remove
Remove the 2nd row lower seat cushion. See Seat
Cushion - Lower - 2nd Row (Remove and Replace).
Remove the rear underhood apron. See Underhood Apron
- Rear (
Bracket - License Plate - Front (NA) (Retrofit)
Retrofit
Clean the front center surface of the front fascia.
Remove the backing from the long horizontal tape strip on the new front
license plate bracket.
Fold the backing of the vertical tape strips out at a 90 degree angle.
Hold the license plate bracket horizontally and
© 2019-2026 Copyright www.tmodel3.com
